Lonsdor-K518ISE-program-BMW-FEM-BDC-key-2

Lonsdor K518ISE program BMW FEM/ BDC key

Programmeur De Clef

Lonsdor K518ISE key programmer manual: how to program BMW FEM/BDC key

Look here:

1- read key information: read out key data and prompt that if the immo need pre-processing

2- process FEM/BD system: backup original coding data, read out EEPROM, generate a service mode EEPROM data, do programming, backup original EEPROM data, restore coding codes

3- make a dealer key: set a key as an dealer key

4- enable a key: set a “disabled” key to “used”

5- disable a key: make a “used”or “lost”key “disabled”

6- delete a key: delete keys that are unnecessary or lost

Three steps: read key info–>pre-process FEM/BDC system–>make a dealer key

In details…

Step 1: read key info

MUST read key information first

Step 2: pre-process FEM/BDC system

MUST DISCONNECT THE BATTERY

1: OBD back up original coding data:

On the car or test platform, connect to FEM/BDC system, then back up original back up coding files via OBD

2: read out EEPROM backup data & generate a service-mode EEPROM:

-> Disassemble FEM/BDC module, find out chip 95128 or 95256, read EEPROM data using a ECU programming tool: VVDI-Prog, Orange5 and the like;

->Copy the EEPROM data into to the Lonsdor K518ISE customfile folder;

->Run the program, read original EEPROM data and generate a service-mode EEPROM, upload data of the service-mode EEPROM, write it into chip 95128 or 95256 with help of a ECU programmer

->Restore FEM/BDC system, supply battery to the car and connect via OBD

Lonsdor-K518ISE-program-BMW-FEM-BDC-key-1

3: programming

->This step need to be done on the BMW FEM/BDC test platform;

->Make sure that Step 1 & 2 is finished

->Connect FEM/BDC system to power supply and connect to the OBD port

4: restore EEPROM data

-> disassemble FEM/BDC module, write original EEPROM data (Step 2) into chip 95128/95256

-> restore FEM/BDC system, connect to OBD

5: restore coding data

-> load the backup coding files (Step 1), restore coding information via OBD

6: pre-processing is complete.

Step 3: make a dealer key

1: Lonsdor K518ISE Programmer read out data, select the will-be key position

2: a “used”key to make a dealer key

All keys lost: enter 32bit ISN codes to make a dealer key

3: put the key near the car immo induction loop

Lonsdor-K518ISE-program-BMW-FEM-BDC-key-2

4: detect the original key, read out immo data

5: put a new key near the car immo induction loop

6: detect the key key, key learn (don’t move the key, keep stable)

7: key learn is complete

Step 4: disable the key

1: Lonsdor K518ISE read out data, select the key ID position to disable

2: put a “used” key near the car induction loop

3: K518ISE system tries to connect to CAS, disable the key with current ID position, disable key successfully

Step 5: enable the key

1: Lonsdor K518ISE read out data, select the key ID position to enable

2: put a “used” key near the car induction loop

3: K518ISE system tries to connect to CAS, enable the key with current ID position, enable key successfully

Step 6: delete the key

1: K518ISE read out data, select the key ID position to delete

2: read FEM/BDC key password

3: delete the key successfully; the key position is blank

THE MOST IMPOERTAN T IPS

1: You must read key info before everything you’ll do

2: to pre-process FEM/BDC, you should pay attention to:

– backup coding codes to continue

– disconnect to the power supply/battery, have a ECU programmer to read EEPROM data, up load data in K518 customfile folder, read new EEPROM data loaded just now, generate service-mode EEPROM data, read service-mode EEPROM data, write data into the chip, install CPU on the car

– ECU programming: need 6 min, with power supply connected

– disconnect to the power supply, disassemble CPU, write the original EEPROM data into the chip, install CPU on the car, connect to the power supply, make sure communicate is successful

– upload coding files (Step 1), restore original coding info to pre-process, then make a dealer key

3: 32bit ISN codes is required to program a new key when ALL KEYS ARE LOST

Job’s done with Lonsdor K518ISE!