How to choose a laptop for Peugeot Diagbox?

Lexia 3 Peugeot Diagbox Computer Requirements:

What is diagbox:

Diagnostic program used by dealers for Peugeot and Citroen vehicles. It only works with the original Chinese and adapters XS Evolution Lexia3.
You can do all as an authorized dealer. This diagnostics software allows you to perform a complete analysis of all models from 1995 to present. Diagnosis is made through the OBD II connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001).

Peugeot diagbox download:

diagbox v7 v8: http://blog.obd2diy.fr/2016/10/07/telecharger-le-logiciel-diagbox-v8-26-v8-19-v8-18-v7-83-v7-76-v7-74-v7-66-v7-58-v7-57/

diagbox software crack: 100% tested

http://www.obd2diy.fr/wholesale/diagbox-v601-software-for-lexia-3-pp2000-peugeot-citroen-diagnostic-tool-1755.html

Psa diagbox computer requirements:
– O.S.: Windows XP, Windows 7, Windows 8, Windows 8.1, Windows 10
– CPU: Intel/AMD 2 GHz or higher
– RAM: 1 GB of system memory
– Hard Drive: 15 GB of available space
– DVD-ROM

Diagbox software user feedback:

I have a 200 year old Dell Latitude something. It runs the software fine. 2nd hand for about £20 with a carry case, charging bits a few years back. Just needed windows re installing and the CPU reseating and the heatsink blowing out.

I have an 11 year old HP Compaq NC 6000 with 2 Ghz Intel Pentium M chip & 2GB ram ( I pimped it up to the motherboards max ) with a 32 bit version of Windows 7.

Peugeot Planet / Diagbox 7.57 works fine on it – it does take a little while to start up either program but once running its perfectly usable.

I use also an old laptop, but replace the disk for a SSD disk, not so expensive, give an amazing performance boost!

My laptop is so old an SSD is out the question
In fact I had to partition the 250GB IDE hard drive first to get it to work as the laptop wouldn’t even recognize the full size of the drive.

Just had to upgrade my laptop as my old one died (more accurately, was killed by my meddling…), the new one has Windows 10. use 10 VMWare Player (free) to avoid a conflict between diagbox and PP. Timesave tip: If you suspend, rather than closing, with Planet running, it restarts in seconds and Planet is still running!

Professional tips you have to read before using Lexia3 Diagbox:

Please create a blank txt file named ‘version’ in C:\   before LEXIA 3installation

  • Install software. Before installation, windows system needs to be English, and until in choosing Language during installation of software, you are free to choose your mother language.
  • Activate software. Under the file “LEXIA3_KEYGEN”, there are the activation pictures for lexia3 and the file “PP2000_KEYGEN” contains the activation pictures for PP2000.
  • It needs registered code for PP2000, but no registered code for lexia3, as for the registered code.

Lexia-3 hardware & software requirements:
Software requires at least Intel Celeron/Pentium III 400 MHz, 128 MB RAM, 50MB free HDD space and USB 1.1 port (USB 2.0 recommended) and Microsoft Windows 98 SR2/2000/XP with the latest service pack installed.

If customer requires, we can prepare ready to work PC.

Please setup the software according to the requirements to hardware and software. Otherwise it will fail to setup and take you much trouble.

Better to install the software on the computer with Windows XP system.

Better to close the Anti-virus software on your computer. Because the Anti-virus may recognize it as a type of virus, it will clear off all the software on the CD.

sales